Search Results

In order to establish hydrogen engines for practical use, it is important to overcome difficulties caused by unique characteristics of hydrogen fuel. A hydrogen engine with direct injection right before top dead center(TDC) and spark ignition has advantages such as prevention of abnormal combustion and realization of high power output near the stoichiometric air-fuel ratio, in comparison with an engine with external mixture. On the other hand, it has been pointed out that ignition and combustion for this type of hydrogen engines should be improved and that further studies on mixture formation of air and injected hydrogen are necessary for the improvement. For the direct injection hydrogen engine, mixture is formed both by air flow inside the combustion chamber and by injected hydrogen jet.

According to authors' previous research, high pressure hydrogen engines with direct injection right before TDC and spark ignition obtain high performance and eliminate almost. abnormal combustion. This study has clarified the mooted points in the flame propagation to adjacent jets and the control of the optimum spark timing and large NOx emissions even in leaner than excess air ratio of λ=2. Nitric oxides (NOx) is the only the pollutant in the exhaust gases emitted by hydrogen engines. It has been found that the NOx formation largely depends on the mixture formation method. In order to operate the engine in a small amount of NOx, an experimental study was carried out to investigate the reduction of NOx and the output power by using dual mixture formation method, external mixture formation and direct injection.

Local heat flux from the flame to the combustion chamber wall, q̇, was measured the wall surfaces of a rapid compression-expansion machine which can simulate diesel combustion. Temperature of the flame zone, T1, was calculated by a thermodynamic two-zone model using measured values of cylinder pressure and flame volume. A local heat transfer coefficient was proposed which is defined as q̇/(T1-Tw). Experiments showed that the local heat transfer coefficient depends slightly on the temperature difference, T1-Tw, but depends significantly on the velocity of the flame which contacts the wall surface.

One of the phenomena accompanying the lightweight/compact/high power output feature of engines is the cylinder bore deformation, which may readily cause increased oil consumption, gas leakage, unusual wear, scuffing, etc.. The authors have had experiences that piston rings had generated contact failure during engine operation (1)*. Such deformation is generated as a combination of the static deformation due to head bolt tightening, crankshaft installation, etc., and the deformation by the operating factors; thermal load and combustion pressure. Countermeasure of design have been made for the former (2)*, and prediction of the deformation during actual operating have been tried using FEM analysis, etc. for the latter (3)*. Therefore, the accurate measurement result have been required strongly, for a long time. But it could not be realized in the past.

In high pressure hydrogen injection hot surface ignition engines under nearly all engine operating conditions combustion pressure vibration is generated just after ignition. As a result of many experimental investigations the true nature for the cause of this interesting phenomenon was found and are listed: (1) This phenomenon probably originates from the extremely high local rate of burning of the hydrogen-air mixture. (2) Accompaning the stronger combustion pressure vibration was an increase in engine vibration and noise with increase in NOx emission and higher piston temperature. (3) Longer ignition delay resulted in a steeper pressure-time diagram which resalted in a stronger combustion pressure vibration. (4) The phenomenon had negligible effect on engine performance. (5) The phenomenon can be prevented by premixing a ceratain quantity of hydrogen gas into the intake air stream. The result was a shortened ignition delay.

A thin film thermocouple with a high accuracy was developed by means of computer analysis, which allowed measurements of instantaneous temperatures and heat fluxes on combustion chamber walls. Conventional Al-alloy and ceramic plates were compared in terms of the heat loss at the upper surface of each piston during combustion, using a gasoline engine and a diesel engine in the series of experiments. It was found by the comparison that the ceramic plates subjected to higher temperatures had greater heat losses in both the gasoline and diesel engines contrary to the anticipation.

The hydrogen combustion characteristics have been studied in a late-injection (near TDC) hot surface ignition engine. As a supplemental experiment, the mode of combustion was observed in a constant volume combustion chamber by the schlieren method. Consequently the combustion process, that was the flame propagation initiated by a hot surface through heterogeneous hydrogen jets, was not the same as that of a diesel engine. The experimental results in test engine showed the optimum number of injection holes and the effect of intake air swirl for better mixture formation. It was observed that the combustion was frequently accompanied by non-negligible combustion pressure vibrations at all engine operating conditions.

The authors developed the optimum thin film thermocouples in terms of materials, shape and dimensions to make instantaneous surface temperature and heat flux measurements of combustion chamber wall in internal combustion engines with accuracy by the computer analysis. And they succeeded to make thin film thermocouple in ceramic piston, by the application of the above technique. Then, the instantaneous surface temperature was measured to obtained the instantaneous heat flux on the ceramic plate fixed on top of the piston.